Treasure Island, FL

Installed faucet and completed toilet rebuild.

Change Order - Needed to run a secondary line around the house to feed the second half of the house approx. 60 more feet because there was two solid beams on the first and the second floor and no way to get from one end to the other. Took the guys two days to dig and send to the other side of the house - Add sink in kitchen pantry - Add sink next to fireplace - Add sink in laundry room

-150 FT TRENCH -CUT NECESSARY DRYWALL -DRILL AND BREAK BLOCK

Major tank rebuild (fill and flush valve) Major tank rebuild ( fill and flush valve) Customer supplied faucet replacement

Remove damaged copper Replace with proper connections Replace shut off valve

Replacing 3/4 shut off Existing has corroded to a point it’s caused a pin hole leak on the plastic pipe Quote is to replace quarter turn valve 1 year warranty

Replacing Kohler shower cartridge Shutting water down to unit Disassembling cover plate and handle Replacing cartridge Reassembling cover plate and handle If repair doesn’t resolve issue Cost will roll into replacement From front wall Using stencil to outline hole that will be made Cutting tile and removing existing shower valve Replacing with new single handle MOEN Shower valve Using a remodel plate to cover hole made for repair 3 year warranty Parts and labor included

Mobilize tools and equipment Prep job site to begin working Drain old heater Replace elements and thermostats to see if that fixes issue Test for leaks and function Demobilize tools and equipment Clean job site 1 year parts and labor warranty, if elements and thermostats do not fix issue then 50% of cost may be rolled into heater replacement job Elements swap did not work but heater is still under warranty so rheem is sending out new mother board to be replaced. Cost is to complete the job with a second trip after new parts arrive

Removing and replacing shut off for south side of building Shutting water down at meter Draining water down and removing damaged shut off Replacing with new quarter turn 1 inch shut off 3 year warranty

Scope of Work: Water Service Line: Install a new 1" Uponor water service line from the city meter to the edge of the building (approx. 40 feet). Meter Installation: City to Install meters approximately 6-8 weeks, Apex will T off the mainline at the building 10x to get water to each unit, once meters are installed by city Apex will cut the Ts out and run the lines to the meters Water Lines to Fixtures: Run new water lines to each fixture in each unit, including: 1 Toilet (cold) 1 Lavatory (hot and cold) 1 Tub/Shower Valve (hot and cold) 1 Kitchen Sink (hot and cold) 1 Ice Maker Box (cold) 1 Water Heater/Point of Use (cold) Main Water Lines: Install main water lines between floors, routing down walls to bottom units and up to top units. Fixture Installation: All fixtures will be equipped with new quarter-turn angle stops and stainless steel braided supply lines. Kitchen hot side will include a dual angle stop to accommodate a dishwasher. Each water heater will have its own shut-off val

Estimate Has to wait to get board approval before we do anything

Turn off water Cut and remove leaking 1/2inch copper tee Install 1/2 pro press slip coupling Install pro press 90 Install 1/2 inch copper tee Turn on water Test for leaks

Turn off water Cut and remove anglestop Install new quarter turn compression anglestop

Running high pressure equipment through cleanout access in garage Scrubbing main sewer line to city main Relieving line of sand build up and debris 1 year warranty on scrub Does not cover baby wipes or tampons Removing and uninstalling existing filtration Replacing with new Apex Supplied product Adding in a bypass valve for future service Comes with a 3 year warranty 1 year labor Parts included

Shut down water to building remove and replace 2 angle stops restore water

Arrived to customers home tested water heater water heater not turning on and not heating water went over to left-hand side of home found broken regulator that supplies gas over to tankless water heater to fix regulator first to see if water heater will kick on if it’s just a gas problem. Need to fix this gas issue first to be able to test for any other issues with water heater. Gas water heater burner is not kicking on due to lack of gas writing up estimates to fix regulator on outside gas line on left-hand side of home. Also checked digital board inside of home could not get any power to that. That panel usually gives you an error code or tells you what the issue is with the water heater Could not get that to turn on but need to fix gas issue first to see if there is any more electrical issues. Customer does not want to move forward with estimate at this time. She wants to get with her builder that said he was going to fix most of the major damage done to home. Customer said if he do

Customer stated no hot water to tankless heater. Throwing error code E003. Turned off heater, water, and gas supply to drain heater and test gas pressure after undoing union coupling for gas line and testing gas pressure and draining tank, restored power to unit and turned water and gas supply back on. Heater was getting hot and gas was functioning properly after diagnostic. Went inside to test all plumbing fixtures for hot water and made sure unit was not giving error code after fixtures were tested and hot water was ran for some time. -check all wiring components and electrical -turn off unit and water supply and drain unit -turn off gas to unit and open union fitting to test gas supply -clean off burner rod and flame rod inside unit to ensure proper operation -turn water and gas back in to unit after gas pressure test and tank drainage -ensure proper operation and function and no error code after testing plumbing fixtures in home -ensure gas and water supply turned back on

Customer stated salt water got into the unit. Recommended replacement due to the fact once salt water gets into these units. They are not salvageable anymore and need replacing. He will be giving us a call when he is ready to move forward.

Estimate

1/2 inch uponor line feeding hose bib has a hole in it. Cut out 3/4 by 1/2 tee and 1/2 90. Install new tee and 90. Connect back to hose bib.

Water heater is leaking from bottom. Will replace existing rheem with same size state water heater. Will drain heater tonight and replace tomorrow.

Estimate: - Will drain and remove toilet from flange - Will investigate issues with flange - If repair is needed will give estimate to do so - Will reset toilet with new wax ring once issue is resolved - Price includes removing and reinstalling toilet. Does not include any repair costs for flange - Also cut ceiling and investigated leak - Found no leaks or moisture

Found kitchen faucet head unscrewed from hose. Screwed head back into hose and found it working properly with no leaks.

Customer had leak coming from compression nut connecting pvc to copper. Removed nut, and made slight adjustment, and reinstalled compression nut, ran lots of water with customer next to me, and no more leaks. Wrote estimate for replacing angle stops. Tyler 8/14/23

Remove existing waste arm and ptrap Install new waste arm and ptrap Test for leaks Clean work area