Tarpon Springs, FL

Shutting water down to unit Using service ports on fixture Flushing unit out with descaling solution While flush is in process doing a maintenance on unit, cleaning filter and condensation trap Process takes about two hours

- Install new 6” sleeve for valve access while backfilling hole

Estimate: - Valve already dug up - Will shut off water to complex - Will cut out old valve and install 1 1/2” square-key gate valve in it’s place - Will connect to existing 1 1/2” sch 80 pipe with sch 80 pipe and fittings - Will allow glue to dry - Will turn water back on to complex and test - Will reinstall valve access sleeve and backfill hole

Turn off water Remove toilet Install wax ring Install new Johnny bolts Reset toilet Test for leaks Heat up flange to soften plastic Cut and remove inside 4inch pvc flange Install new 4inch pvc flange Tapcon flange to conrete floor Reinstall toilet

Customer called about kitchen sink not draining. I ran water in the sink and it filled up immediately. This line needs to be snaked and hydroscrubed. I will snake from cleanout under sink.

Home owner is checking on requirements of grinder pump specs that are dictated by City

Home owner declined estimate at this time

Estimate: - Will shut off water to toilet at angle stop - Will drain and remove toilet from flange - Will inspect flange for damage - Will snake through toilet drain to clear blockage - If flange is in good condition, will test toilet with new wax ring and bolts - Flange is broken and needs repair - Snaked 175 feet and clog did not clear - Will return with camera to investigate

Turn off water Remove old anglestop Install new quarter turn compression anglestop Remove toilet Cable mainline Reinstall toilet Test for leaks IF WATER COMES FROM THE BOTTOM OF THE TOILET DURING A CLOG IT COULD BE DUE TO A BAD WAX SEAL A TOILET REMOVAL AND RESET WOULD BE RECOMMENDED Includes a free camera

Estimate: - Will drain and remove old toilet in master bathroom - Will clean caulking from floor and replace wax ring on flange - Will install American Standard ADA Elongated Cadet Pro toilet - Will hook up to existing water supply - Will caulk bottom edges - Will turn water on to toilet and test - Will haul away old toilet After pulling toilet found flange broken. Needs to be repaired or replaced. Estimate: - Will drill pilot holes through tile and concrete - Will install repair ring on top of flange - Will anchor repair ring to concrete - Will continue with toilet installation

Access main line thru clean out in back yard

Expansion tank on the water heater is cracked and is leaking Will take out old tank Will install new expansion tank with tape and dope

Toilet is backing up into shower. Cable from cleanout in yard.

Estimate: - Will pull out refrigerator - Will install 1/4” refrigerator supply - Will test water fixture on refrigerator - Will push refrigerator back into place

Turn off water Sweat broken copper out Sweat new copper stubout into copper T Sweat new hose bib onto stub out Test for leaks

Replace angle stop and toilet supply line

Turn off power and water to tankless heater Remove tankless heater from wall Install new tankless heater Turn on power and water Test for leaks

Upon arrival, found mainline to be clogged upon further diagnosis. Found the effluent pump to not be working and two have been burnt out. Pump could have burned out from becoming clogged or the drainfield backing up into the pump pit causing pump to run constantly

Main line goes from pvc to copper at the house. Pvc male that is threaded into copper is cracked. Cut out 1 foot section of copper and pvc and put back together with pvc male, propress female, propress slip coupling and small piece of copper.

Remove old fill valve Install new fill valve

Chip and remove concrete around shower drain Inside cut and remove old drain Glue in new drain patch concrete around drain with sand mix Install new shower pan Plug with test ball and test to ensure no leaks CHANGE ORDER Disconnect water lines from tub valve Disconnect tub drain and overflow Carefully cut around tub, lift out of place and set out of way Once new tile is set around surround reset tub in place Reconnect water lines to tub valve Reconnect drain and overflow Fill and test

Old 1/2 hp effluent pump is not working Check wires to pump with voltage tester and the pump is receiving power I pulled the pump out and lifted the float switch straight up and pump will not turn on The tank the pump sits in is not sealed and the lid is in bad condition and need to be replaced with the pump Pump may be clogged with sewage We will replace effluent pump with a 3/4 hp grinder pump because effluent pump only pumps sewage and a grinder pump grinds sewage up before pumping it down the sewer line which greatly reduces chances of a clogged pump and with perform much better So we will install and new 3/4 Grinder pump and tank with a 3 year parts and labor warranty

Dig up and evaluate why grinder pump is not turning on

THIS IS AN L SHAPED SHOWER, AND WILL REQUIRE A CUSTOM PAN INCLUDING THE FOLLOWING: -REMOVE FLOOR -REMOVE PAN -REMOVE DRAIN AND REPLACE -TAKE TILE OUT 12 IN UP WALL -PAN WILL NEED PRE-SLOPED -INSTALL NEW CUSTOM PAN INCLUDES PERMITTING AND INSPECTIONS APEX IS NOT RESPONSIBLE FOR REPLACEMENT OF TILE 10 YEAR WARRANTY ON MATERIALS

Diagnose any issues with heater. Heater not getting power from electrical box on wall behind it.